Abstract
This study investigated the crystal structure and mechanical properties of copper foil electroplated by adjusting gelatin and chloride ions from 0 to 100 ppm. There was increased formation of spherical crystals and surface roughness on the surface of the electroplated layer when the gelatin was added, and the direction of..... More

Abstract
Electroplated copper has been used as wiring in electronic circuit boards and as cathode materials for secondary batteries, and its usage has expanded into the construction industry because of its convenient production and high economic value. During the electroplating process, various parameters, such as crystal phase and size, can affect..... More

Abstract
This study manufactured Fe-Cr-Ni-based alloy (HK30) using the metal injection molding (MIM) process and investigated the microstructure and room·high temperature mechanical properties of the material. The effect of hot isostatic pressing (HIP) on properties was also examined. The average grain sizes were 24.1 µm for an MIM specimen and 29.1..... More

Abstract
Since strength and ductility have a trade-off relationship in Al alloys, controlling these properties using heat treatments requires careful attention to the dissolution and evolution of the reinforcing phases. In this study, the effects of solution and aging treatments on the microstructure and mechanical properties of Al-5.2Si-3.4Cu-0.28Mg alloy were investigated...... More

Abstract
Since their development in the 1970s ZrO₂ ceramics have been shown to be promising alternative materials for total hip arthroplasty (THA) and total knee arthroplasty (TKA). However, ZrO₂ is so brittle that in vivo failure can result from fracture of the ceramic femoral head and fracture of the ceramic acetabular..... More

Abstract
To study the effect of Al and Zr contents on the microstructural changes and tensile properties of Ni-Al-Bronze alloy, seven specimens were cast with different Al and Zr contents. The microstructure observation revealed that all specimens were composed of β’ and κ phases in a α matrix. With increasing Al..... More

Abstract
Feasibility studies are performed to determine the suitability of a novel simple synthesis technique for fabricating a new Ti alloy with improved strength and ductility, while exhibiting lower cell toxicity. Through consolidating pure Ti powders under a C atmosphere at elevated temperatures, a bulk form of the Ti alloy, in..... More

Abstract
The effect of ultrasonic melt treatment (UST) on the microstructure and mechanical properties of Al-7Si-0.35Mg (A356) casting alloys was investigated. The particular aim of this study was to analyze the mechanism involved in the strengthening of the A356 alloys when fabricated by UST. The UST had little effect on the..... More

Abstract
Despite of many attractive properties of TiN, the current concern about the TiN focuses on its low fracture toughness below the ductile-brittle transition temperature. To improve its mechanical properties, the approach generally utilized has been the addition of a second phase to form composites and to make nanostructured materials. In..... More

Abstract
Intermetallic compounds (IMCs) developed on the interface between a solder alloy and its bonding pads are an important factor in the failure of electronic circuits. In this study, the mechanical behaviors of the IMCs formed in the Cu-Ni-Sn ternary alloy system are investigated. Presumably, Ni can act as a diffusion..... More

Abstract
Despite of the many attractive properties of TiO₂, its low fracture toughness limits many industrial applications. To improve its fracture toughness, the approach commonly utilized has been the addition of a second phase, to form composites, and to make nanostructured composites. In this regard, highly dense nanostructured TiO₂ and TiO₂-graphene..... More

Abstract
The aim of this study is to establish an optimized hot-press sintering condition for aluminum matrix composites (AMCs) by analyzing their sintered microstructure and mechanical properties. The fabricated AMCs in this study consisted of a blend of commercial Ecka Alumix 431 powder, and Al-Si/SiC_p powder manufactured by gas atomizer (Al-Si/SiC_p)...... More

Abstract
Fe-(20, 45 wt%) Gd intermetallics were vacuum arc melted as the mother alloy of a neutron shielding and absorbing material. The structure of the cast Fe-20 wt% Gd intermetallics had primary dendrites with a short width of about 2 μm, which became coarse with increasing Gd content. The final compositions..... More

Modeling and Simulation

Abstract
Yttrium Aluminum Garnet (YAG) single crystal has received much attention as the high power solid-state laser’s key component in industrial and medical applications. Various growth methods have been proposed, and currently the induction-heating Czochralski (IHCZ) growth method is mainly used to grow YAG single crystal. Due to the intrinsic properties..... More

Plastic Working & Materials Processing

Abstract
Laser surface carburizing can be achieved by a laser alloying mechanism, which includes melting the graphite coated substrate and dissolution of the graphite in the liquid state. The drawback of laser carburizing is that process-induced cracks frequently form on the carburized surface as a result of carbon enrichment and the..... More

Abstract
The aim of this study is to optimize the microstructure and mechanical properties of Ti-39Nb-6Zr (TNZ40) for bio-implant applications. TNZ40 was designed to have a low elastic modulus (~40 GPa) and good biocompatibility. However, the alloy shows relatively low strength compared to other titanium alloys for bio-implant. In the present..... More

Abstract
Open cell Cu foam, which has been widely utilized in various industries because of its high thermal conductivity, lightweight and large surface area, was successfully joined with Cu plate by diffusion bonding. To prevent excessive deformation of the Cu foam during bonding process, the bonding pressure should be lower than..... More

Abstract
The low mechanical properties of SiC limit its wide application despite many attractive properties. To improve the mechanical properties, a second phase has been generally added to make a nanostructured composite. In this respect, graphene was evaluated as the reinforcing agent of SiC. SiC-graphene composites were sintered within 2 min..... More

Abstract
CoTi and ZrO₂ nanopowders were mechanochemically synthesized from CoTiO₃ and Zr powders according to the reaction (2CoTiO₃ + 3Zr → 2CoTi + 3ZrO₂). The milled powders were then consolidated by pulsed current-activated sintering within two minutes under an applied pressure of 80MPa. The average hardness and fracture toughness of the..... More

Abstract
In this paper, we demonstrate that the microstructure and mechanical properties in the Ti₄₀Zr₁₀Cu₃₆Pd₁₄ alloy can be tailored by controlling the cooling rate during solidification. A lower cooling rate increases the volume fraction of crystalline phase such as B2 but decreases the free volume of the glassy matrix. The increase..... More

Abstract
In this work, both experimental and numerical studies were conducted to investigate the densification behavior of stainless steel 316L (STS 316L) powders during hot isostatic pressing (HIP), and to characterize the mechanical properties of HIPed specimens. The HIP experiments were conducted with gas atomized STS 316L powders with spherical particle..... More